Login: GUEST @ JH4XSY.14.JNET1.JPN.AS [Tsuchiura]
home | newest check | boards | help index | log | ps | userlogin | send sysop | slog | status forward | bcm news | users | version | remove cookie
G8MNY > ATV 18.10.26 18:40l 145 Lines 7895 Bytes #28 (0) @ WW
BID : 8388_GB7CIP
Subj: Black & Burst Sync Buffer
Path: JH4XSY<IW0QNL<HB9ON<HB9ON<PI8ZTM<VE3CGR<VE3TOK<VE3KPG<GB7CIP
Sent: 261018/0925Z @:GB7CIP.#32.GBR.EURO #:8388 [Caterham Surrey GBR] $:8388_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To : ATV@WW
By G8MNY (CQTV 2001, new to Packet Feb 05)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
WHATS IT FOR?
When genlocking video sources together sometimes there is cable or camera
crosstalk from the genlock source feed when distributed with ordinary video as
the genlock source. This circuit will solve that problem while still allowing
the use of a non genlock camera as the genlock source master rather than the
use of a PAL colour SPG.
This 6 transistor circuit (4 PNP & 2 NPN) is a precision vision buffer amp, or
sync black & burst stripper amp, providing 3 outputs. It uses no hard to find
or obsolete ICs that many video projects need, indeed many constructors will
find all the bits are in their junk box. All transistors can be 100mA general
purpose silicon small signal types as transistor performance has mainly been
designed out of this circuit.
Construction can be UGLY, MATRIX or PCB, but be careful if using Stripboard as
the paralleled inductance lines can cause instability!
CIRCUIT
2x amp Sync Sep DC clamp Video Amp
ﾚﾄﾄﾄﾂﾄﾄﾄﾄﾄﾄﾂﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾂﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾂﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾄﾂﾄﾄﾄﾄﾂﾄﾄﾄﾂﾄ<+12-15V
ｳ ｳ R6 ｳ/e R12 R15 R17 ｳ
ｳ R4 22R ﾚﾄﾄｴ T3 2K7 470R 3R3 +ｳ680u
ｳ 470R ｳ ｳ ｳ\ ﾚﾄﾄﾄｴ Phase2 ｳ ｳ ===
R2 ｳ ｳ/e ｳ ｳ _ｳ_ ｳ VC2 ｳ ｳ/e _ｳ_
1M ﾃﾄﾄﾄﾄｴ C2 ｳ ｳ /_\ ｳ 100p/\ ﾃﾄﾄｴT6
ｳ ｳ T2 ｳ\ u1 ｳ ｳ ｳ ｳ ﾚﾄｴﾃﾄﾄｿ ｳ ｳ\ + R18
ｳ ｳ ﾃﾄﾄｴﾃﾄﾄｴ ｳ ｳ ｳ ｳ/ ｳ ｳ ﾃﾄｴﾃﾄﾂﾄ68Rﾄ(o
Video ｳ ｳ ｳ+ ｳ ｳ ｳ ｳ ｳ R14 ｳ ｳ/ ｳ1500ｳ
In & ｳ ｳ/ ﾃﾄﾄｴﾃﾄﾄ)ﾄﾄﾄﾄ)ﾄﾄﾄﾄﾄﾄﾁﾄﾄﾄ)ﾄﾁﾄ4K7ﾂﾁﾄﾄﾄｴT5 ｳ uF ﾃﾄ68Rﾄ(o
o)ﾄﾂﾄｴﾃﾄﾅﾄｴT1 470R C3 ｳ ｳ ｳ ｳ ｳ\e ｳ ｳ R19
o)ﾄｴ u1 ｳ ｳ\e R7 4u7 ｳ ｳ ｳ ｳ/e ﾃﾄﾄﾄﾄﾙ ﾀﾄ68Rﾄ(o
outｳ ｳ ﾃﾄﾄﾄﾄﾄﾄｴ ｳ ﾃﾄﾄﾄﾄﾂﾄﾄﾄﾄﾄ)ﾄﾄﾄﾄｴT4 ｳ R20
75R R3 100R R8 ｳ 2K2 10K ｳ ｳ\ R16
R1 M39 R5 330R R9 R10 R11 ﾃﾄﾄﾄﾄﾄﾄｴ 180R 1/2W
SW1 o ｳ /\ｳ VC1 ｳ/\ 1M ｳ ｳ /\ R13 ｳ+ ｳ
Term/' ｳ ===100 100R ｳ n27ｳ VR2 2K7 ===C6 ｳ
ｳ ｳ ｳ\pF /VR1 ｳ C5=== /22K ｳ ｳ4u7 ｳ
ﾀﾄﾄﾄﾄﾁﾄﾄﾄﾁﾄﾄﾄﾄﾄﾄﾁﾄﾄﾄﾄﾄﾄﾁﾄﾄﾄﾄﾁﾄﾄﾄﾄ)ﾄﾄﾄﾄﾄﾁﾂﾄﾄﾄﾄﾄﾁﾄﾄﾄﾄﾄﾄﾁﾄﾄﾄﾄﾄﾄﾄﾄｿ
Phase1 Gain Syncｳ SW2 ｳ _ｳ_
Compﾀﾄ/'oﾄﾄﾙ
HOW IT WORKS
The video input can be looped through or terminated with R1 (this can be made
from 2x 150R in parallel if needed). Vision is fed to a high input impedance
(>200k) transistor amp T1 & T2 with a gain of just over 2. The low value of
pull up resistor R4 & the use of the PNP emitter resistor R6, ensure very good
colour linearity. Presets VR1 and VC1 set the gain & colour phase (delay) of
the amp.
The 2V P-P video feeds a lightly biased T3 PNP transistor to make a sync
stripper stage. Its collector is high during syncs and VR2, R11 & C5 form a
sync & colour burst timing window that will operate the blanking stage T4 PNP
transistor during picture time. Resistor R10 in series with C5 lets fast sync
rise time edges through. Mode switch SW2 will allows composite or black & burst
modes by disabling the blanking stage. Capacitor C5 can be omitted if the
colour burst is not wanted.
The amplified video also feeds through C3, then it is clamped at 0.6V below
from the half supply rail with D1. Using a 2V P-P video level this point sets
the black video level to approximately the bias rail with standard sync
amplitude of the genlock source without the need for a proper black level
clamp. When the collector of T3 is 0.5V more negative than the half rail
(during picture time) T4 is turned on, shorting out the picture video that has
gone through R14 & VC2 to the half rail.
Transistors T5 & T6 make up a unity gain video buffer amp, with a low value of
pull down resistor R16 to provide good syncs while driving 3 loads. Again a low
value of pull up resistor R15 & the use of the PNP emitter resistor R17, ensure
very good video & colour linearity. VC2 trimmer sets the HF gain & colour
phase. Good LF performance is ensured with a large value output C7 & each of
the 3 output source impedances will be very close to the ideal 75R with the use
of 68R as the feeding resistors.
WAVEFORMS
ﾚﾄﾄｿ
__ｳYeﾃﾄﾄｿ
ｳWhｳ__ｳCyﾃﾄﾄｿ
ｳ ｳ ｳ__ｳGnﾃﾄﾄｿ
ｳ ｳ__ｳ ｳ__ｳMaﾃﾄﾄｿ
Colourｳ ｳ__ｳ ｳ__ｳRdﾃﾄﾄｿ
Burstｳ ｳ__ｳ ｳ__ｳBlｳ
Line ﾚﾄｿ ｳVideo inputｳ__ｳ ｳ__ｳBk Burstﾚﾄｿ No Picture
Sync _ｳ ｳ_ｳ 100% Colour ｳ__ｳ ｳ__ _ｳ ｳ________________________
ｳ ｳ ｳ ｳ . Bars ｳ__ｳ ｳ ｳ ｳ ｳ ｳ Video Output ｳ
ｳ ｳ ﾀﾄﾙ . ｳ ｳ ｳ ﾀﾄﾙ Sync, burst & Black ｳ
ｳ ｳ . ｳ ｳ ｳ ｳ
ﾀﾄﾄﾙ . ﾀ ﾀﾄﾄﾙ ﾀ
. . .
+12V__ . . __
ｳ \ . T3 Sync Seperator . ｳ ｳ T4 Blanking current
ｳ `. . Waveform . .ｳ..ｳ____........................
...ｳ.....`........................... Clamp Diodeｳ ___...---'''
---' `------------------------' Current |...---'''
T4 Blanking Transistor on
SETTING UP
The circuit should draw about 35mA from 12-14V DC anything wildly different
should be investigated. Using an oscilloscope check the 2x amplifier is working
OK. Then in black & burst mode, check the sync separator output, it should have
inverted line syncs from 12V to 6V with a lazy back edge. Check at frame rate
that there is no LF problems with the syncs.
Scoping the output buffer (T6 Collector) you should have just syncs & burst
with no picture content at about 6V DC. Adjust the burst window preset VR2 so
that blanking starts just after the burst. In composite mode there should be
around 2V P-P. Terminate all the outputs into 75� & check that the buffer amp
output stays nearly constant (showing that the buffer amp has nearly zero R
output impedance). Scope the output on one of the terminations, & adjust gain
preset VR1 for unity overall gain of the circuit. Also check at frame rate that
there are no LF droop problems.
Colour phase is best set up with a colour bar source and a vectorscope using
identical leads. Adjust the 2 HF phase presets for best phase & amplitude match
on the vector display. It will be seen that the two presets do have slightly
different effects & by alternate tweeks the correct phase & amplitude can be
obtained. Switching to black & burst mode the phase of the bursts should not
alter.
But for those without a vectorscope & colour bars, adequate phase setup can be
done by subtraction comparison using an evenly lit brightly coloured card in
front of a colour camera & a dual beam scope with channel subtraction.
Calibrate the scope by probing the video input with both probes and adjusting
the timebase & gains to show a single colourful line. Put the scope into
subtract mode, and tweek channel gains & scope probes adjustments to produce
the best nulled out blank line. Now move a probe to one of the terminated
outputs and adjust the 2 HF phase presets for best burst & colour picture
carrier null.
IN USE
In composite mode the buffer amp works as well as can be expected. In the back
& burst mode the video blanking is only approx at the black level & will depend
on source sync levels. The exact amount of picture vision left after blanking
may depend on the component layout. Both of these should not have any affect on
the kit being genlocked.
Why Don't U send an interesting bul?
73 de John G8MNY @ GB7CIP
前のメール | 次のメール